Progress Report - July 2024

The restoration of 23-003 continued throughout July. On July 18th, after earlier removal of the cockpit instruments, instrument panel, throttle quadrant and floor boards, Bill Kinkaid was able to remove the control column. He then removed the glareshield (shown in the image above).

On the morning of July 20th, the interior (seats, side walls, partitions, carpet, etc.) along with the thrust reversers, engine cowlings and a set of new tires were removed from building 14 to Millennium LLC who have volunteered to store these items for us making more room around the airplane and wing.

“A major milestone was reached on July 23rd, when Bill Kinkaid announced that the cockpit had been disassembled to the point that we can start removing the cabin wiring. This will begin with the removal of the circuit breakers from their panels. Bill discovered that the airplane was built without break plugs between the circuit breaker and its wiring. They are 'hard wired'! This will require each wire to be labeled as the circuit breaker is removed.

Read the full newsletter by clicking the button below.

Download Full Newsletter

< Older Post

Newer Post >

Progress Report - July 2026

By Kristen Nuss • August 3, 2026

How time flies! A short four years ago, on July 20, 2022, we made our trip to Bartow Executive Airport, Bartow, Florida, to do an inspection of 23-003 to see if she was restorable. Today 23-003 is in Wichita, Kansas within a few hundred feet south of the Lear Jet factory where she was built in 1964. CLJF now owns 23-003 and the restoration project is well along! The latest work by the volunteers has been working on the removal of the aft cabin floor in order to proceed with the structural inspections of the fuselage. It is a slow process because of the large amount of sealant used between the floor and the surrounding structure that has to be manually cut loose before the floor can be removed. Also, all the parts removed from the airplane continue to be identified, inspected, and dispositioned for service, replacement or overhaul. A big THANK YOU to all the volunteers! We greatly appreciate all that you do!

Progress Report - June 2026

By Kristen Nuss • July 2, 2026

Throughout the construction going on in bays 1 and 10 in building 14, our dedicated volunteers continue to make significant progress. On June 4, 2026 they removed the leading edges from the horizontal stabilizer. This will allow us to start the structural inspection. Once completed, it will be transported to DAS Aviation for restoration. Also, on June 4th, the wing from 23-028, that we acquired for parts, was removed from the wing dolly and installed on the ‘rotisserie’ by volunteers Jim Tidball, Dan DeMott, Hartney Hummer and Al Goodwin. Next, we will check the condition of the wing by performing a leak test on each wing and start removing parts from various wing systems. The daunting task of making a new wiring harness to replace the existing 62-year-old wiring harness continues. On June 9th we caught volunteers Bud Ledom, Rob Bielman and Dave Dendurant hard at pouring over drawings identifying the wires, connectors, switches, etc. A Memorandum of Agreement (MOA) between the CLJF and Embry-Riddle Aeronautical University (ERAU) was signed on May 28th. This MOA details the responsibilities of each of us for the restoration of the landing gear. On June 10, 2026, Jim Long and his son, Zach, of Noble Jet, picked up the landing gear retraction actuators and the box of various hydraulic actuators. There they will be tested and rebuilt. Thank You Noble Jet!!

Progress Report - May 2026

By Kristen Nuss • May 31, 2026

This month we removed the skin from the top of the aft fuselage, above the engine pylons. Three more fuselage skins are in the process of being removed as shown in the photo below. Removal of the skins is the only way for us to do visual inspections of the structure and to give access for future X-ray inspections. Areas of suspected corrosion, circled in the following photo, will be exposed with the removal of these skins. Visual and X-ray inspections will be conducted to verify the condition of the underlying structure. Then, if required, repairs or replacement of the structure will be accomplished. On May 22, 2026 the landing gear and several actuators were loaded onto Chris Marshall’s truck by Chris, Ron Forshee and Dick Kovich to be driven to Florida by Chris and his wife, Darla, where they will be restored. The landing gear will be restored by Embry-Riddle Aeronautical University (ERAU) in Daytona, Florida. The landing gear actuators and a box of miscellaneous smaller hydraulic actuators will be tested and rebuilt by Noble Jet in Fort Lauderdale, Florida. A huge Thank you to both ERAU and Noble Jet!!!